|
|
 |
350-401 Valid Exam Simulator - 350-401 New Exam Materials & Implementing Cisco Enterprise Network Core Technologies 350-401 Encor - Royalholidayclubbed
|
|
RHC Destination Reviews
Who Is Harpy?
Need More Information?
What is your reason for wanting to be certified with 350-401 Valid Exam Simulator? I believe you must want to get more opportunities. As long as you use 350-401 Valid Exam Simulator learning materials and get a 350-401 Valid Exam Simulator certificate, you will certainly be appreciated by the leaders. As you can imagine that you can get a promotion sooner or latter, not only on the salary but also on the position, so what are you waiting for? Just come and buy our 350-401 Valid Exam Simulator study braindumps. Royalholidayclubbed's Cisco 350-401 Valid Exam Simulator exam training materials are absolutely trustworthy. We are dedicated to provide the materials to the world of the candidates who want to participate in IT exam. According to our overall evaluation and research, seldom do we have cases that customers fail the 350-401 Valid Exam Simulator exam after using our study materials.
CCNP Enterprise 350-401 Royalholidayclubbed will never disappoint you.
350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Valid Exam Simulator exam cram materials will try our best to satisfy your demand. So you have nothing to worry about, only to study with our 350-401 Latest Real Test exam questions with full attention. And as we have been in this career for over ten years, our 350-401 Latest Real Test learning materials have became famous as a pass guarantee.
Royalholidayclubbed will help you with its valid and high quality 350-401 Valid Exam Simulator prep torrent. 350-401 Valid Exam Simulator questions & answers are compiled by our senior experts who with rich experience. Besides, we check the update about 350-401 Valid Exam Simulator training pdf every day.
Cisco 350-401 Valid Exam Simulator - It is enough to help you to easily pass the exam.
The whole world of 350-401 Valid Exam Simulator preparation materials has changed so fast in the recent years because of the development of internet technology. We have benefited a lot from those changes. In order to keep pace with the development of the society, we also need to widen our knowledge. If you are a diligent person, we strongly advise you to try our 350-401 Valid Exam Simulator real test. You will be attracted greatly by our 350-401 Valid Exam Simulator practice engine. .
If you want to through the Cisco 350-401 Valid Exam Simulator certification exam to make a stronger position in today's competitive IT industry, then you need the strong expertise knowledge and the accumulated efforts. And pass the Cisco 350-401 Valid Exam Simulator exam is not easy.
350-401 PDF DEMO:
QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html
QUESTION NO: 2
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.
QUESTION NO: 3
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.
QUESTION NO: 4
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.
QUESTION NO: 5
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.
Huawei H12-821_V1.0 - You never know what you can get till you try. Docker DCA - But God forced me to keep moving. Our ISACA CRISC exam torrent can help you overcome this stumbling block during your working or learning process. In order to avoid wasting too much time in preparing for the exam, Royalholidayclubbed provides you with Cisco SAP C-S4CFI-2504 dumps that can help you pass the test in the short period of time. So many our customers have benefited form our Salesforce Marketing-Cloud-Consultant preparation quiz, so will you!
Updated: May 28, 2022
|
Copyright © 2006-2007 by RHC.
All rights
reserved. |
---------------
If you don't find what you are looking for here
to help you resolve your timeshare scam or Royal Holiday problem
please write to us at:
harpy @ royalholidayclubbed.com
www . Royal Holiday Clubbed . com
|
|