350-401 Test Dumps Demo & Cisco Training 350-401 Tools - Implementing Cisco Enterprise Network Core Technologies 350-401 Encor - Royalholidayclubbed

RHC Destination Reviews

Who Is Harpy?

Need More Information?

With the 350-401 Test Dumps Demo training pdf, you can get the knowledge you want in the actual test, so you do not need any other study material. If the 350-401 Test Dumps Demo exam is coming and the time is tense, it is better to choose our 350-401 Test Dumps Demo test engine dumps. 350-401 Test Dumps Demo test engine can simulate the actual test during the preparation and record the wrong questions for our reviewing. And so many of our loyal customers have achieved their dreams with the help of our 350-401 Test Dumps Demo exam questions. Your aspiring wishes such as promotion chance, or higher salaries or acceptance from classmates or managers and so on. Immediately after you have made a purchase for our 350-401 Test Dumps Demo practice dumps, you can download our 350-401 Test Dumps Demo study materials to make preparations.

It is better than 350-401 Test Dumps Demo dumps questions.

CCNP Enterprise 350-401 Test Dumps Demo - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) They have a keen sense of smell in the direction of the exam. By using these aids you will be able to modify your skills to the required limits. Your Reliable Dumps 350-401 Free Download certification success is just a step away and is secured with 100% money back guarantee.

You give us a trust and we reward you for a better future. With 350-401 Test Dumps Demo guide torrent, you may only need to spend half of your time that you will need if you didn’t use our products successfully passing a professional qualification exam. In this way, you will have more time to travel, go to parties and even prepare for another exam.

Cisco 350-401 Test Dumps Demo - So, hurry to take action.

Our windows software and online test engine of the 350-401 Test Dumps Demo exam questions are suitable for all age groups. At the same time, our operation system is durable and powerful. So you totally can control the 350-401 Test Dumps Demo study materials flexibly. It is enough to wipe out your doubts now. If you still have suspicions, please directly write your questions and contact our online workers. And we will give you the most professions suggestions on our 350-401 Test Dumps Demo learning guide.

Many times getting a right method is important and more efficient than spending too much time and money in vain. Our Royalholidayclubbed team devote themselves to studying the best methods to help you pass 350-401 Test Dumps Demo exam certification.

350-401 PDF DEMO:

QUESTION NO: 1
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 2
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 3
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 4
Which statement about multicast RPs is true?
A. RPs are required for protocol independent multicast sparse mode and dense mode.
B. By default, the RP is needed only to start new sessions with sources and receivers.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers
D. RPs are required only when using protocol independent multicast dense mode.
Answer: B
Explanation:
A rendezvous point (RP) is required only in networks running Protocol Independent Multicast sparse mode (PIM-SM).
By default, the RP is needed only to start new sessions with sources and receivers.
Reference:
https://www.cisco.com/c/en/us/td/docs/ios/solutions_docs/ip_multicast/White_papers/rps.html
For your information, in PIM-SM, only network segments with active receivers that have explicitly requested multicast data will be forwarded the traffic. This method of delivering multicast data is in contrast to the PIM dense mode (PIM-DM) model. In PIM-DM, multicast traffic is initially flooded to all segments of the network. Routers that have no downstream neighbors or directly connected receivers prune back the unwanted traffic.

QUESTION NO: 5
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

Now let's take a look at why a worthy product of your choice is our NREMT EMT actual exam. Although our Royalholidayclubbed cannot reduce the difficulty of GIAC GRTP exam, what we can do is to help you reduce the difficulty of the exam preparation. We are so confident in our Salesforce Marketing-Cloud-Consultant study materials because they have their own uniqueness. UiPath UiPath-SAIAv1 - While others are surprised at your achievement, you might have found a better job. API API-936 - However, we believe that with the excellent quality and good reputation of our study materials, we will be able to let users select us in many products.

Updated: May 28, 2022

by RHC.

---------------

If you don't find what you are looking for here

to help you resolve your timeshare scam or Royal Holiday problem

please write to us at:

harpy @ royalholidayclubbed.com

Link Partner Directory

www . Royal Holiday Clubbed . com

sitemap