350-401 Sample Exam - Cisco Valid Practice Questions Implementing Cisco Enterprise Network Core Technologies 350-401 Encor Book - Royalholidayclubbed

RHC Destination Reviews

Who Is Harpy?

Need More Information?

Why we let you try our 350-401 Sample Exam exam software free demo before you purchase? Why we can give you a promise that we will fully refund the money you purchased our software if you fail 350-401 Sample Exam exam with our dump? Because we believe that our products can make you success. As the 350-401 Sample Exam exam continues to update, our software will be always updating with it. Ranking the top of the similar industry, we are known worldwide by helping tens of thousands of exam candidates around the world. To illustrate our 350-401 Sample Exam study materials better, you can have an experimental look of them by downloading our 350-401 Sample Exam demos freely. In order to make you be rest assured to buy our 350-401 Sample Exam exam software, we provide the safest payment method –PayPal payment.

CCNP Enterprise 350-401 Do not worry.

You do not need to spend money; because our 350-401 - Implementing Cisco Enterprise Network Core Technologies (350-401 ENCOR) Sample Exam test questions provide you with the demo for free. If you decide to buy our Vce 350-401 Torrent study question, we can promise that we will send you the latest information every day. As is known to us, it must be of great importance for you to keep pace with the times.

The most notable feature of our 350-401 Sample Exam learning quiz is that they provide you with the most practical solutions to help you learn the exam points of effortlessly and easily, then mastering the core information of the certification course outline. Their quality of our 350-401 Sample Exam study guide is much higher than the quality of any other materials, and questions and answers of 350-401 Sample Exam training materials contain information from the best available sources.

Cisco 350-401 Sample Exam - Perhaps you do not understand.

For years our team has built a top-ranking brand with mighty and main which bears a high reputation both at home and abroad. The sales volume of the 350-401 Sample Exam test practice guide we sell has far exceeded the same industry and favorable rate about our products is approximate to 100%. Why the clients speak highly of our 350-401 Sample Exam exam dump? Our dedicated service, high quality and passing rate and diversified functions contribute greatly to the high prestige of our products. We provide free trial service before the purchase, the consultation service online after the sale, free update service and the refund service in case the clients fail in the test.

As long as you are convenient, you can choose to use a computer to learn, you can also choose to use mobile phone learning. No matter where you are, you can choose your favorite equipment to study our 350-401 Sample Exam learning materials.

350-401 PDF DEMO:

QUESTION NO: 1
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. On
C. Auto
D. Passive
Answer: B
Explanation:
Restrictions for Link Aggregation:
You can bundle all eight ports on a Cisco 5508 Controller into a single link.
Terminating on two different modules within a single Catalyst 6500 series switch provides redundancy and ensures that connectivity between the switch and the controller is maintained when one module fails. The controller's port 1 is connected to Gigabit interface 3/1, and the controller's port 2 is connected to Gigabit interface 2/1 on the Catalyst 6500 series switch. Both switch ports are assigned to the same channel group.
LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.
Once the EtherChannel is configured as on at both ends of the link, the Catalyst switch should not be configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation
Protocol (PAgP) but be set unconditionally to LAG. Because no channel negotiation is done between the controller and the switch, the controller does not answer to negotiation frames and the LAG is not formed if a dynamic form of LAG is set on the switch. Additionally, LACP and PAgP are not supported on the controller.
If the recommended load-balancing method cannot be configured on the Catalyst switch, then configure the LAG connection as a single member link or disable LAG on the controller.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/configuration- guide/b_cg75/b_cg75_chapter_0100010.html

QUESTION NO: 2
What is the difference between a RIB and a FIB?
A. The FIB is populated based on RIB content
B. The RIB is used to make IP source prefix-based switching decisions
C. The RIB maintains a mirror image of the FIB
D. The FIB is where all IP routing information is stored
Answer: A
Explanation:
CEF uses a Forwarding Information Base (FIB) to make IP destination prefix-based switching decisions.
The FIB is conceptually similar to a routing table or information base. It maintains a mirror image of the forwarding information contained in the IP routing table. When routing or topology changes occur in the network, the IP routing table is updated, and those changes are reflected in the FIB. The
FIB maintains next-hop address information based on the information in the IP routing table. Because there is a one-to-one correlation between FIB entries and routing table entries, the FIB contains all known routes and eliminates the need for route cache maintenance that is associated with earlier switching paths such as fast switching and optimum switching.
Note: In order to view the Routing information base (RIB) table, use the "show ip route" command.
To view the Forwarding Information Base (FIB), use the "show ip cef" command. RIB is in Control plane while FIB is in Data plane.

QUESTION NO: 3
Which technology provides a secure communication channel for all traffic at Layer 2 of the OSI model?
A. IPsec
B. Cisco Trustsec
C. MACsec
D. SSL
Answer: C
Explanation:
MACsec, defined in 802.1AE, provides MAC-layer encryption over wired networks by using out- of
-band methods for encryption keying. The MACsec Key Agreement (MKA) Protocol provides the required session keys and manages the required encryption keys. MKA and MACsec are implemented after successful authentication using the 802.1x Extensible Authentication Protocol (EAP-TLS) or Pre
Shared Key (PSK) framework.
A switch using MACsec accepts either MACsec or non-MACsec frames, depending on the policy associated with the MKA peer. MACsec frames are encrypted and protected with an integrity check value (ICV). When the switch receives frames from the MKA peer, it decrypts them and calculates the correct ICV by using session keys provided by MKA. The switch compares that ICV to the ICV within the frame. If they are not identical, the frame is dropped. The switch also encrypts and adds an ICV to any frames sent over the secured port (the access point used to provide the secure MAC service to a
MKA peer) using the current session key.
Reference: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst9300/software/release/16-
9/configuration_guide/sec/b_169_sec_9300_cg/macsec_encryption.html
Note: Cisco Trustsec is the solution which includes MACsec.

QUESTION NO: 4
Refer to the exhibit. A port channel is configured between SW2 and SW3. SW2 is not running a
Cisco operating system. When all physical connections are mode, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?
A. The port-channel interface lead balance should be set to src-mac
B. The port-channel trunk is not allowing the native VLAN.
C. The port-channel should be set to auto.
D. The port channel on SW2 is using an incompatible protocol.
Answer: D
Explanation:
The Cisco switch was configured with PAgP, which is a Cisco proprietary protocol so non-Cisco switch could not communicate.

QUESTION NO: 5
Which feature does Cisco TrustSec use to provide scalable, secure communication throughout a network?
A. security group tag number assigned to each user on a switch
B. security group tag ACL assigned to each router on a network
C. security group tag ACL assigned to each port on a switch
D. security group tag number assigned to each port on a network
Answer: D
Explanation:
Cisco TrustSec uses tags to represent logical group privilege. This tag, called a Security Group Tag
(SGT), is used in access policies. The SGT is understood and is used to enforce traffic by Cisco switches, routers and firewalls . Cisco TrustSec is defined in three phases: classification, propagation and enforcement.
When users and devices connect to a network, the network assigns a specific security group.
This process is called classification. Classification can be based on the results of the authentication or by associating the SGT with an IP, VLAN, or port-profile (-> Answer A and answer C are not correct as they say "assigned ... on a switch" only. Answer D is not correct either as it says "assigned to each router").

ACAMS CAMS - It absolutely has no problem. Juniper JN0-637 - Today's era is a time of fierce competition. You may find that there are a lot of buttons on the website which are the links to the information that you want to know about our Google Associate-Data-Practitioner exam braindumps. Amazon CLF-C02-KR - You can think about whether these advantages are what you need! And if you don't know which one to buy, you can free download the demos of the Amazon CLF-C02 study materials to check it out.

Updated: May 28, 2022

by RHC.

---------------

If you don't find what you are looking for here

to help you resolve your timeshare scam or Royal Holiday problem

please write to us at:

harpy @ royalholidayclubbed.com

Link Partner Directory

www . Royal Holiday Clubbed . com

sitemap